Courses

Manual Design of Reinforced Concrete Structures

Manual Design of Reinforced Concrete Structures
300 USD 240 USD
دبلومة التصميم الانشائي-الكود الامريكي
3 Courses
901 Lessons in 96 Chapters
385 Hours & 20 Minutes
0 Student in 0 Country
  Diploma Info   Buy Now
Lessons
223 Lessons in 27 Chapters
Duration
97 Hours & 1 Minutes
Students
0 Student in 0 Country
Instructor
Ragab Elmasry Senior Structural Design Engineer

Course Overview


التعريف بالكورس

يؤهلك الكورس الي فهم اساسيات التصميم الانشائي والتصميم اليدوي لجميع العناصر الخرسانية وفق لمتطلبات الكود الامريكي والسعودي وهي المرحلة الاول والاهم لاي مهندس تصميم قبل البدئ باستخدام برامج التصميم الانشائي

كذالك يجب علي جميع المهندسين فهم التصميم لمانيوال سواء تصميم او تنفيذ

وسوف نقوم بالتطبيق علي مشروعين

المشروع الاول : مشروع مانيوال مبني 5 طوابق

المشروع الثاني : مشروع مانيوال مبني 10 طوابق

Course Curriculum
  Expand All     Collapse All
Chapter 01 - Lecture 113 Lessons
 6:39:00
01-01 - Introduction of Reinforced Concrete Design
 3:27:00
01-02 - ACI Design Course - 1 - Building Codes
 0:15:00
01-03 - ACI Design Course - 2 - Matrial
 0:17:00
01-04 - ACI Design Course - 3 - Matrial
 0:16:00
01-05 - ACI Design Course - 4 - Matrial
 0:15:00
01-06 - ACI Design Course - 5 - Matrial
 0:16:00
01-07 - ACI Design Course - 6 - Failure of sections
 0:16:00
01-08 - ACI Design Course - 7 - Type of loads
 0:16:00
01-09 - ACI Design Course - 8 - Type of loads
 0:16:00
01-10 - ACI Design Course - 9 - Type of loads
 0:16:00
01-11 - ACI Design Course - 10 - Design methods
 0:17:00
01-12 - ACI Design Course - 11 - Design methods
 0:16:00
01-13 - ACI Design Course - 12 - Reduction moment of inertia
 0:16:00
Chapter 02 - Lecture 28 Lessons
 3:36:00
02-01 - Design of Sections
 1:43:00
02-02 - ACI Design Course - 1 - Design of sections
 0:16:00
02-03 - ACI Design Course - 2 - Failure of sections
 0:16:00
02-04 - ACI Design Course - 3 - Design of Singly reinforced section
 0:17:00
02-05 - ACI Design Course - 4 - Design of Singly reinforced section
 0:16:00
02-06 - ACI Design Course - 5 - Design of Singly reinforced section
 0:16:00
02-07 - ACI Design Course - 6 - Design of Singly reinforced section
 0:16:00
02-08 - ACI Design Course - 7 - Design of Doubly reinforced section
 0:16:00
Chapter 03 - Lecture 37 Lessons
 3:34:00
03-01 - Design of Short Columns
 2:00:00
03-02 - ACI Design Course - 2 - Classification of columns
 0:16:00
03-03 - ACI Design Course - 3 - Type of Straning Action on columns
 0:16:00
03-04 - ACI Design Course - 4 - Requirements of vertical R.F.T
 0:15:00
03-05 - ACI Design Course - 5 - Requirements of Transfer R.F.T
 0:16:00
03-06 - ACI Design Course - 6 - Design of Short columns Subject to Axial loads only
 0:15:00
03-07 - ACI Design Course - 7 - Design of Short columns Subject to Axial Loads plus Uniaxial Moment
 0:16:00
Chapter 04 - Lecture 48 Lessons
 3:42:00
04-01 - Design of Long Columns
 1:49:00
04-02 - ACI Design Course - 1 - Introduction of Long Columns
 0:16:00
04-03 - ACI Design Course - 2 - Braced & Unbraced Columns
 0:16:00
04-04 - ACI Design Course - 3 - Braced & Unbraced Columns
 0:16:00
04-05 - ACI Design Course - 4 - Short or Long
 0:16:00
04-06 - ACI Design Course - 5 - Moment Magnification method For Braced (NonSway) Columns
 0:17:00
04-07 - ACI Design Course - 6 - Moment Magnification method For UnBraced (Sway) Columns
 0:16:00
04-08 - ACI Design Course - 7 -Example
 0:16:00
Chapter 05 - Lecture 512 Lessons
 5:22:00
05-01 - Design of Solid Slabs
 2:25:00
05-02 - ACI Design Course - 1 - Introduction of Solid slabs
 0:17:00
05-03 - ACI Design Course - 2 - mechanism of load transfer
 0:15:00
05-04 - ACI Design Course - 3 - Type Of Solid slabs
 0:16:00
05-05 - ACI Design Course - 4 -Design of one Way Solid slabs - Calculate Ts of slabs
 0:16:00
05-06 - ACI Design Course - 5 -Design of one Way Solid slabs - Calculate Loads of slabs
 0:16:00
05-07 - ACI Design Course - 6 - Take Strips -Approximate method
 0:16:00
05-08 - ACI Design Course - 7 - 3 Moment Equation
 0:16:00
05-09 - ACI Design Course - 8 - R.F.T Of Solid slabs
 0:16:00
05-10 - ACI Design Course - 9 - Example of One way slabs
 0:17:00
05-11 - ACI Design Course - 10 - Two way slabs
 0:16:00
05-12 - ACI Design Course - 11 - Example of Two way slabs
 0:16:00
Chapter 06 - Lecture 68 Lessons
 3:39:00
06-01 - Design of Hollow Block Slabs
 1:50:00
06-02 - ACI Design Course - 1 - mechanism of load transfer
 0:16:00
06-03 - ACI Design Course - 2 - Advantage Of Hollow Block Slabs
 0:15:00
06-04 - ACI Design Course - 3 - Type Of H.B Slabs
 0:15:00
06-05 - ACI Design Course - 4 - Design Of one Way H.B Slabs
 0:16:00
06-06 - ACI Design Course - 5 - Example Of one Way H.B Slabs
 0:16:00
06-07 - ACI Design Course - 6 - Design Of Two Way H.B Slabs
 0:16:00
06-08 - ACI Design Course - 7 - Example Of Two Way H.B Slabs
 0:15:00
Chapter 07 - Lecture 714 Lessons
 5:33:00
07-01 - Design of Flat Slabs
 2:10:00
07-02 - ACI Design Course - 1 - mechanism of load transfer
 0:15:00
07-03 - ACI Design Course - 2 - Elastic support & Rigid support
 0:16:00
07-04 - ACI Design Course - 3 - Advantage Of Flat slab & Type Of Flat slabs
 0:15:00
07-05 - ACI Design Course - 4 - Minimum Thickness of Flat Slab
 0:14:00
07-06 - ACI Design Course - 5 - The Direct Design Method
 0:16:00
07-07 - ACI Design Course - 6 - Design Of Flat Slabs
 0:16:00
07-08 - ACI Design Course - 7 - Design Of Strips
 0:16:00
07-09 - ACI Design Course - 8 - Design Of Strips
 0:16:00
07-10 - ACI Design Course - 9 - Design Of Strips
 0:16:00
07-11 - ACI Design Course - 10 - R.F.T Details
 0:16:00
07-12 - ACI Design Course - 11- Example of flat slab
 0:16:00
07-13 - ACI Design Course - 12 - Punching Shear
 0:15:00
07-14 - ACI Design Course - 5 - Minimum Depth of Beams
 0:16:00
Chapter 08 - Lecture 87 Lessons
 2:53:00
08-01 - Introduction Of Beam - Load Distribution
 1:18:00
08-02 - ACI Design Course - 1 - Type Of Beams
 0:15:00
08-03 - ACI Design Course - 2 - Type Of Beams
 0:16:00
08-04 - ACI Design Course - 3 - Type Of Beams
 0:17:00
08-05 - ACI Design Course - 4 - Beams Position
 0:17:00
08-06 - ACI Design Course - 6 - Calculate Loads On Beams
 0:15:00
08-07 - ACI Design Course - 7 - Load Distribution
 0:15:00
Chapter 09 - Lecture 96 Lessons
 2:12:00
09-01 - Design of Beams Due To Flexure
 0:51:00
09-02 - ACI Design Course - 1 - How To Calculate B.M.D
 0:16:00
09-03 - ACI Design Course - 2 - How To Calculate B.M.D
 0:16:00
09-04 - ACI Design Course - 3 - Design Of Beams
 0:16:00
09-05 - ACI Design Course - 4 - R.F.T Requires
 0:16:00
09-06 - ACI Design Course - 5 - Type Of Sections
 0:17:00
Chapter 10 - Lecture 109 Lessons
 3:36:00
10-01 - Design of Beams Due To Shear
 1:35:00
10-02 - ACI Design Course - 1 - Introduction Of Shear
 0:15:00
10-03 - ACI Design Course - 2 - How Ot Resist Shear Force
 0:15:00
10-04 - ACI Design Course - 3 - Draw S.F.D
 0:15:00
10-05 - ACI Design Course - 4 - Draw S.F.D
 0:15:00
10-06 - ACI Design Course - 5 - Critical Section Of Shear
 0:16:00
10-07 - ACI Design Course - 6 - Design of Section Due To Shear
 0:15:00
10-08 - ACI Design Course - 7 - Design of Section Due To Shear
 0:15:00
10-09 - ACI Design Course - 8 - Example Of Design Beam
 0:15:00
Chapter 11 - Lecture 114 Lessons
 1:47:00
11-01 - Design of Beams Due To Torsion
 1:00:00
11-02 - ACI Design Course - 1 - Introduction To Torsional Moment
 0:15:00
11-03 - ACI Design Course - 2 - Design Of Torsional Moment
 0:16:00
11-04 - ACI Design Course - 3 - Example Of Torsional Moment
 0:16:00
Chapter 12 - Lecture 1214 Lessons
 5:38:00
12-01 - Design of Stairs
 2:19:00
12-02 - ACI Design Course - 1 - Introduction Of Stairs
 0:15:00
12-03 - ACI Design Course - 1 - Introduction Of Stairs
 0:16:00
12-04 - ACI Design Course - 2 - Starter Beam
 0:16:00
12-05 - ACI Design Course - 3 - Spring Slabs
 0:15:00
12-06 - ACI Design Course - 4 - Spring Stairs
 0:16:00
12-07 - ACI Design Course - 5 - Stairs Details
 0:15:00
12-08 - ACI Design Course - 6 - Statical Systems Of Stairs
 0:16:00
12-09 - ACI Design Course - 7 - Statical Systems Of Stairs
 0:15:00
12-10 - ACI Design Course - 8 - Statical Systems Of Stairs
 0:15:00
12-11 - ACI Design Course - 9 - Statical Systems Of Stairs
 0:15:00
12-12 - ACI Design Course - 10 - Statical Systems Of Stairs
 0:15:00
12-13 - ACI Design Course - 11 - Steps Of Design Stairs
 0:15:00
12-14 - ACI Design Course - 12 - Example of stairs
 0:15:00
Chapter 13 - Lecture 136 Lessons
 2:17:00
13-01 - Introduction of Design Foundations
 1:02:00
13-02 - ACI Design Course - 1 - Advantage of Foundations
 0:15:00
13-03 - ACI Design Course - 2 - Type Of Footings
 0:15:00
13-04 - ACI Design Course - 3 - Type Of Shallow Foundations
 0:15:00
13-05 - ACI Design Course - 4 - Chose The Foundations Type
 0:15:00
13-06 - ACI Design Course - 5 - Concept of Design Footings
 0:15:00
Chapter 14 - Lecture 149 Lessons
 3:33:00
14-01 - Design Of Isolated Footing
 1:26:00
14-02 - ACI Design Course - 1 - Steps of Design Isolated Footings
 0:16:00
14-03 - ACI Design Course - 2 - Concrete Dim Of Isolated Footings
 0:16:00
14-04 - ACI Design Course - 3 - Calculate Stresses
 0:17:00
14-05 - ACI Design Course - 4 - Check One Way Shear
 0:16:00
14-06 - ACI Design Course - 5 - Check Punching (Two Way Shear)
 0:16:00
14-07 - ACI Design Course - 6 - Calculate Moment
 0:16:00
14-08 - ACI Design Course - 7 - Calculate R.F.T
 0:15:00
14-09 - ACI Design Course - 8 - Example
 0:15:00
Chapter 15 - Lecture 155 Lessons
 1:29:00
15-01 - Design Of Footing Subject to (M,P)
 0:27:00
15-02 - ACI Design Course - 1 - Steps of Design Isolated Footings Subject to M,P
 0:15:00
15-03 - ACI Design Course - 2 - Con.Dim & Check Stresses
 0:16:00
15-04 - ACI Design Course - 3 - One & Two Way Shear & Design
 0:16:00
15-05 - ACI Design Course - 4 -Example of Footing (M,P)
 0:15:00
Chapter 16 - Lecture 163 Lessons
 0:42:00
16-01 - Design Of Strip footing
 0:13:00
16-02 - ACI Design Course - 2 -Example of strip footing
 0:13:00
16-03 - ACI Design Course - 1 - Design Of Strip Footings
 0:16:00
Chapter 17 - Lecture 178 Lessons
 3:08:00
17-01 - Design Of Combined Footing
 1:20:00
17-02 - ACI Design Course - 1 - Concept Of Design Combined Footings
 0:15:00
17-03 - ACI Design Course - 2 - Con.Dim Of Combined Footings
 0:15:00
17-04 - ACI Design Course - 3 - Calculate Stresses
 0:16:00
17-05 - ACI Design Course - 4 - Straining Actions
 0:16:00
17-06 - ACI Design Course - 5 - Design Of Combined Footing
 0:16:00
17-07 - ACI Design Course - 6 - Example of combined footing
 0:15:00
17-08 - ACI Design Course - 7 - Example of combined footing
 0:15:00
Chapter 18 - Lecture 188 Lessons
 3:12:00
18-01 - Design Of Strap beam
 1:21:00
18-02 - ACI Design Course - 1- Concept Of Strap beams
 0:16:00
18-03 - ACI Design Course - 2- Design of Strap beam
 0:16:00
18-04 - ACI Design Course - 3- Design of Strap beam
 0:16:00
18-05 - ACI Design Course - 4- Design of Strap beam
 0:16:00
18-06 - ACI Design Course - 5- Example of Strap beam
 0:15:00
18-07 - ACI Design Course - 6- Example of Strap beam
 0:16:00
18-08 - ACI Design Course - 7- Design Of Combined Footing ( Case 2 )
 0:16:00
Chapter 19 - Lecture 196 Lessons
 3:12:00
19-01 - Manual Project 1
 1:53:00
19-02 - ACI Design Course - 1 - Design of Slab
 0:16:00
19-03 - ACI Design Course - 2 -Design of Stair
 0:16:00
19-04 - ACI Design Course - 3 - Design of Beams
 0:16:00
19-05 - ACI Design Course - 4 - Design of Columns
 0:15:00
19-06 - ACI Design Course - 5 - Design of Footing
 0:16:00
Chapter 20 - Lecture 208 Lessons
 3:33:00
20-01 - Design Of Raft Foundation
 1:43:00
20-02 - ACI Design Course - 1 - Intro Of Design Raft
 0:15:00
20-03 - ACI Design Course - 2 - Statical System Of Design Raft
 0:16:00
20-04 - ACI Design Course - 3 - Manual Design Of Design Raft
 0:16:00
20-05 - ACI Design Course - 4 - Manual Design Of Design Raft
 0:15:00
20-06 - ACI Design Course - 5 - Manual Design Of Design Raft
 0:16:00
20-07 - ACI Design Course - 6 - Manual Design Of Design Raft
 0:16:00
20-08 - ACI Design Course - 7 - Manual Design Of Design Raft
 0:16:00
Chapter 21 - Lecture 2110 Lessons
 5:06:00
21-01 - UBC 97-Equivalent Static Load
 2:38:00
21-02 - ACI Design Course - 1 - Equivalent static load UBC 97
 0:16:00
21-03 - ACI Design Course - 2 - Equivalent static load UBC 97
 0:16:00
21-04 - ACI Design Course - 3 - Equivalent static load UBC 97
 0:16:00
21-05 - ACI Design Course - 4 - Time Period UBC 97
 0:17:00
21-06 - ACI Design Course - 5 - Calculate base shear
 0:17:00
21-07 - ACI Design Course - 6 - Distribution of lateral force on each floor
 0:17:00
21-08 - ACI Design Course - 7 - Distribution of lateral force on each Shear wall
 0:16:00
21-09 - ACI Design Course - 8 - Distribution of lateral force on each Shear wall
 0:17:00
21-10 - ACI Design Course - 9 - Distribution of lateral force on each Shear wall
 0:16:00
Chapter 22 - Lecture 2213 Lessons
 6:12:00
22-01 - Asce 7-16 -Equivalent Static Load
 2:53:00
22-02 - ACI Design Course - 1 - Equivalent static load ASCE 7-16
 0:16:00
22-03 - ACI Design Course - 2 - Equivalent static load ASCE 7-16
 0:16:00
22-04 - ACI Design Course - 3 - Time Period ASCE 7-16
 0:17:00
22-05 - ACI Design Course - 4 - Calculate Base shear ASCE 7-16
 0:16:00
22-06 - ACI Design Course - 5 - Seismic Design Category ASCE 7-16
 0:16:00
22-07 - ACI Design Course - 6 - Distribution of lateral force on each floor ASCE 7-16
 0:17:00
22-08 - ACI Design Course - 7 - Distribution of lateral force on each Shear wall
 0:17:00
22-09 - ACI Design Course - 8 - Distribution of lateral force on each Shear wall
 0:16:00
22-10 - ACI Design Course - 9 - Distribution of lateral force on each Shear wall
 0:17:00
22-11 - ACI Design Course - 10 - Distribution of lateral force on each Shear wall
 0:17:00
22-12 - ACI Design Course - 11 - Example
 0:17:00
22-13 - ACI Design Course - 12 - Example
 0:17:00
Chapter 23 - Lecture 237 Lessons
 2:39:00
23-01 - Wind loads UBC 97
 1:02:00
23-02 - ACI Design Course - 1 - Wind Loads Theory
 0:16:00
23-03 - ACI Design Course - 2 - Wind Loads Calculation UBC 97
 0:16:00
23-04 - ACI Design Course - 3 - Wind Loads Calculation UBC 97
 0:16:00
23-05 - ACI Design Course - 4 - Wind Loads Calculation UBC 97
 0:16:00
23-06 - ACI Design Course - 5 - Wind Loads Calculation UBC 97
 0:16:00
23-07 - ACI Design Course - 6 - Wind Loads Calculation UBC 97
 0:17:00
Chapter 24 - Lecture 246 Lessons
 2:49:00
24-01 - Wind loads Asce 7-16
 1:29:00
24-02 - ACI Design Course - 1 - Wind Loads Theory
 0:15:00
24-03 - ACI Design Course - 2 - Wind Loads Calculation ASCE 7-16
 0:16:00
24-04 - ACI Design Course - 3 - Wind Loads Calculation ASCE 7-16
 0:16:00
24-05 - ACI Design Course - 4 - Wind Loads Calculation ASCE 7-16
 0:16:00
24-06 - ACI Design Course - 5 - Wind Loads Calculation ASCE 7-16
 0:17:00
Chapter 25 - Lecture 2513 Lessons
 5:11:00
25-01 - Design of Shear walls
 2:08:00
25-02 - ACI Design Course - 1 - Shear walls
 0:16:00
25-03 - ACI Design Course - 2 - Shear walls
 0:16:00
25-04 - ACI Design Course - 3 - Shear Walls Position
 0:16:00
25-05 - ACI Design Course - 4 - Shear Walls Position
 0:16:00
25-06 - ACI Design Course - 5 - Shear Walls Position
 0:16:00
25-07 - ACI Design Course - 6 - Shear Walls Position
 0:15:00
25-08 - ACI Design Course - 7 - Distribution of lateral force on each Shear wall
 0:15:00
25-09 - ACI Design Course - 8 - Distribution of lateral force on each Shear wall
 0:14:00
25-10 - ACI Design Course - 9 - Distribution of lateral force on each Shear wall
 0:15:00
25-11 - ACI Design Course - 10 - Shear walls R.F.T Requirments
 0:15:00
25-12 - ACI Design Course - 11-Design of S.walls
 0:15:00
25-13 - ACI Design Course - 12-Design of S.walls
 0:14:00
Chapter 26 - Lecture 268 Lessons
 2:10:00
26-01 - ACI Design Course 1 - Design Of Slab
 0:15:00
26-02 - ACI Design Course 2 - Design Of Stair
 0:16:00
26-03 - ACI Design Course 3 - Design Of Beams
 0:17:00
26-04 - ACI Design Course 4 - Design Of Wind loads
 0:17:00
26-05 - ACI Design Course 5 - Design Of Seismic loads
 0:16:00
26-06 - ACI Design Course 6 - Design Of Columns
 0:16:00
26-07 - ACI Design Course 7 - Design Of Shear walls
 0:17:00
26-08 - ACI Design Course 8 - Design Of Footing
 0:16:00
Chapter 27 - Lecture 273 Lessons
 3:37:00
27-01 - Manual Project 2 ( Tower )
 2:07:00
27-02 - SBC 1101 - SBC 304 Codes
 1:14:00
27-03 - ACI Design Course - 1 - ACI & SBC
 0:16:00

Kayan Academy

Kayan Academy is a specialized company in training, technical support, and services for Engineering and Graphics software. Since 2009 till now Kayan Academy has adopted an innovative approach to integrated solutions in CAD & BIM technology by implementing strategies based on commitment, quality, customer satisfaction, and high return on investment. During this period Kayan Academy has expanded its services in Egypt and Gulf. In 2017 Kayan Academy opened its office in Alexandria and Cairo to deliver the most updated services to its customers

Find Us On

Contact Us

+201020819686
+2010 260 89 086
+2011 19 561 245
+2010 17 207 636
+964 784 649 7506
+2015 51 181 765
Info@kayan-co.org
مكرم عبيد - مدينه نصر - القاهرة
https://goo.gl/maps/sk8ikbPv64DwRwEw9
----------------------------------
شارع عدلي يكن- جليم - الإسكندرية
https://goo.gl/maps/7KmDZhoe4bmxkV3Z9
Copyright © Kayan Academy 2026
Powered by ® Teachal